EFFORTLESS CLEAN. LIMITLESS ADVENTURE.

The world's most portable pressure washer designed for bikes.

Powered by a robust lithium-ion battery, the Rehook Cordless Bike Pressure Washer delivers the freedom to clean anywhere with no compromise on performance. With up to 40 minutes of continuous cleaning power and adjustable water pressure, it ensures a thorough but delicate jet wash for your bike. Load the foam canister with one of our plant-based bike cleaning products, for a deep foam that is as kind to your bike as it is to the environment.

No mains power required - High capacity battery and digital motor enables 40 minutes of battery powered pressure wash time.

No mains water supply needed - just grab a water container and get cleaning!

Designed for bikes and the great outdoors.

Get yours at https://rehook.bike/products/rehook-cordless-bike-pressure-washer 

 

What’s in the case?

 

Rehook Cordless Pressure Washer Diagram

Cordless pressure/jet washer with 300W brushless motor

Lithium-ion 21V 15Ah battery & charger

6-in-1 bike spray lance

Foam canister & nozzle

2.5m water hose with adapter & water filter

Water bottle adapter & short hose

Rehook Recycled Microfibre Cloth

6mm allen/hex key

 

Digital display

Battery display 

The display indicates the remaining battery capacity in increments of 20%. This is updated when the trigger is pressed. To check battery level, release the trigger then press trigger once again.

Pressure display

The pressure display indicates the current water pressure from 1 to 30.

Pressure adjustment

Use the + and - buttons to adjust the water pressure. With the pressure on 30 (maximum) the run time will be reduced below 30 minutes.

 

Water connection

Water hose and filter

The hose and filter provided can be used to provide water from a bucket or any body of freshwater, such as a lake or stream.

To connect the hose, simply pull down the blue section of the hose connector and push the hose onto the water connection point (1) of the main unit. 

Note: The pressure washer is designed to pump its own water supply using the filter provided. If the unit is attached to a mains water supply then the water pressure will not damage the unit, but releasing the trigger will not stop the flow of water. It is therefore recommended that the unit is only used with the provided filter or bottle attachment.

Pressure washer hose and water filter

Warning
⚠️ Always use filter - loose debris in water can damage the inner workings
⚠️ Do not use with salt water - this will corrode the inner workings

hose connection for pressure washer

Bottle attachment

The bottle adapter can also be used as a replacement for the hose and filter. To use the bottle adapter (2), unscrew and remove the hose connection from the standard hose (3) and attach to the short hose (4). 

Only use the bottle connection with fresh clean water. Do not put cleaning fluids through the bottle attachment as these can damage the innerworkings. Instead use the foam canister for any cleaning fluids.

 

Spray attachments

Spray Lance

With 6 different spray settings this attachment has settings that are Perfect for cleaning all areas of your bike. Simply push and twist the lance (5) into the end of the main unit (6) to firmly attach it. The lance can be removed in a similar manner.

For best performance position the lance at 2 to 14 inches from the bicycle. Always start from further away and move closer to the bicycle to check the pressure is not going to damage your paintwork or other components.

mobile pressure washer with spray lance and foam

Foam Canister

Push and twist the foam canister (7) to firmly connect it to the main unit. 

Fill the foam canister with our plant-based  Rehook Universal Bike Cleaner or Bio Drivetrain Degreaser, for a deep foam that is as kind to your bike as it is to the environment. The canister can be unscrewed from the foaming attachment in order to fill it with cleaning liquid.

Use the foam canister at a greater distance for wider coverage.

pressure washer foam canister foam spray for bikes

Warning
⚠️ If using a degreaser, be mindful 
not to get any on disc brake rotors or pads

 

Lance Settings

pressure washer lance with multiple settings

0 Degrees
A direct high pressure beam used for cleaning the most stubborn dirt from hard to reach areas such as drivetrains.

15 Degrees
The default setting which creates a flat pressurised beam, ideal for general cleaning.

25 Degrees
A wide pressurised beam which covers a larger area.

40 Degrees
A extra wide flat pressurised beam for cleaning large areas.

Tap
a direct stream of heavy water covering a greater distance.

Shower
a drenching mist used to give a heavy rinse.

Warning
⚠️ Do not twist lance while spraying

 

Battery

Removing

Push the blue removal button (10) at the back of the battery and slide the battery backwards out of the unit.

lithium ion battery powered pressure washer for bikes

Charging

Charge the battery with the charger provided. The charger can be inserted into the top of the battery. Attach the charger to the battery prior to plugging the charger into mains power. The battery has intelligent charging protection. The indicator light shows red when charging and green when fully charged.

charger for cordless pressure washer for bicycles

Installing

Slot the battery into the base of the main unit (8) to install the battery. Ensure the battery is firmly in place.
 

The 21V Lithium Ion battery included with the pressure washer has a 15 Ah capacity, giving a runtime of around 40 minutes.

installing a battery on a pressure washer
installing a battery on a mobile pressure washer

Warning
⚠️ Use only with battery and charge provided
⚠️ Do not use if battery is showing signs of damage
⚠️ Store in a cool dry environment, out of direct sunlight
⚠️ Avoid contact with water
⚠️ Do not disassemble the battery case

 

Storage & Maintenance

Store in a dry place out of direct sunlight, using the carry case provided.

After use, remove the hose from the water source and hold the trigger to ensure the hose and pressure washer are completely drained.

A microfibre cloth is provided to help dry the pressure washer after use.

 

Warning
⚠️ Store water filled components outside the carry case until completely clean and dry
⚠️ Keep water away from battery and charger

 

Usage

Once the pressure washer is setup as described in the previous steps it can be operated by squeezing the trigger. 

For a thorough clean we suggest the following:

Pre rinse - Rinse the bulk of the dirt from you bike using the 15 degree setting on the spray lance. Switch to the 0 degrees for more stubborn dirt in hard to reach areas such as drivetrains.

Foam - Use the foam canister with Rehook Universal Cleaner to cover your bike in foam. You can optionally switch to Rehook Bio Degreaser to foam the drivetrain, taking care not to get any on disc brake rotors or braking surfaces.

Rinse - Let the foam soak for a moment before rinsing the foam and loosened dirt away with the spray lance on either the shower and 15 degree setting.

Dry - Dry off the bike with a microfiber cloth or towel.

Finish - Finish off with Rehook Frame peedwax for added shine and to help safeguard your bike from moisture, UV rays, and environmental contaminants.

Lube - Lube or wax your dried chain with Rehook Bio Chain Wax or Oil as required.

 

bike cleaning kit for bike cleaner and foam bike cleaner

Troubleshooting

Nothing happens when I pull the trigger

Ensure that the battery is charged and fully inserted into the main unit.
To check if the battery is in working condition, connect the battery to the charger and plug into mains. The charger will show a red light if the battery is working properly.

 

The motor is running but no water is coming out of the pressure washer

Check that the hose is connected firmly to the unit.
Ensure the filter is fully submerged in water and the hose is free from kinks and bends.
It may take upto 10 seconds before water is sprayed depending on the length of hose you are using.
If the problem persists, debris may be trapped in the mechanism. Flush the pressure washer by connecting the unit to a hose pipe connected to a mains water supply and holding the trigger for 10 seconds.

 

The battery level jumps from a high number to zero

The battery monitor displays the current battery usage in increments of 20%. The display is updated each time the trigger is pulled. If you hold the trigger for a prolonged period of time then the display will not update.

 

The end of the spray lance is loose

The lance can be tightened using the silver bolt in the centre of the spray settings. Tighten the bolt using the allen key provided (9) or the H6 tool bit from your Rehook Plus or Rehook mini multi-tool. The screw should hold the end of the lance in place while remaining loose enough for the spray setting to be changed by twisting it.

 

If you need additional support you can reach us at hello@rehook.bike

 

Check out the rest of the range

The ultimate solution to elevate your bike maintenance game. From pristine frames to smooth-running drivetrains, unleash a new level of cleanliness and performance on your rides.

REVIVE YOUR RIDE

complete bike care kit with bike cleaner and cleaning brushes for bikes
Back to blog

Leave a comment

Please note, comments need to be approved before they are published.

EXCLUSIVE OFFERS AND THE LATEST UPDATES BY EMAIL

FOLLOW THE NEWSLETTER